jack the car remove the rear left wheel first look at the gas funnel rail under the plastic shield # bolts you'll be surprise with the mud accumulate there, that's why in my case the vent tube was so rust that it was almost split in two, so I cut the bad lenghs and replace with a nylon pipe, erase t...

Washing and waxing my Vibe today here's nice pic
https://servimg.com/view/11097178/426][/url]
https://servimg.com/view/11097178/425][/url]

The reason I'm posting this is because many vibe owner told me that the wiper feel a bit slow . The pivots gets dry and rusty so the only way to fix the problem. Make sure wiper are in park. unbolt both arms and remove them, remove (left and right) plastic cover (Clip under the rubber) and one each ...

I use a 1 1/4 x 42 inc steel corner, welded on both side I notch were the 2 engine support bar bolts are. I grease It all, I,m good for couple years. https://i45.servimg.com/u/f45/11/09/71/78/20210711.jpg https://i45.servimg.com/u/f45/11/09/71/78/20210712.jpg https://i45.servimg.com/u/f45/11/09/71/7...

I listed for US customer too.

https://www.ebay.ca/itm/114737183295
I'm selling a pontiac vibe 03-08 microphone shift knob ready to screw in.

yes the gasketif its the original are orange, they leak on the bank one corner replace it with the black one made by felpro

Mine 299,999 KM and 3,000 on th trip meter

2.5% tinted back side windows, sports red caliper, rear trunk spoiler, hood scoop front bumper and hardtop painted satin black, sports console, homemade microphone shifter.

Welcome Dude,

That's a nice project you have now, looking forward to see some pics.

Good one Dude! my passenger seat is occupied 80% of the time

Same here, It was already replaced 1 year ago with another tataka and received another letter 2 months ago for replacement with part:19355534 recall was done this morning took 45 minutes at GM dealer. Don't mess with this recall....

No It's just a decoration, I won't cut the hood dude! and if I dont'like I will remove It.

https://i45.servimg.com/u/f45/11/09/71/78/20180912.jpg https://i45.servimg.com/u/f45/11/09/71/78/20180913.jpg https://i45.servimg.com/u/f45/11/09/71/78/20180914.jpg https://i45.servimg.com/u/f45/11/09/71/78/20180915.jpg I just installed a new modern radio all digital, with mini SD card reader,USB 3...

There is a stud holding tranny support that is welded in the back center If you don't oil it or WD-40 before, It could unweld and you are going to have a hard time to unbolt It. It took me 1 hour to cut It with a hand hafl steel saw by holding to other end with a vise grip!!!, when reassemble I put ...

On my 2006 I have 246,000KM my oil consumtion is about 1/8 pint per 15,000KM. I use DuraLube for many years and this stuff is awesome product to keep engine clean and idling perfectly.

A very good compression test should read between 195 to 210 PSI
If between 175 to 190 PSI piston rings are tired..
below 175 PSI your cylinder bores are scratch enough to loose a lot of compression and more oil consumption.

I don't believe on seafoam, did you ever heard on this fantastic product? https://www.youtube.com/watch?v=DC7fd3yuQFw Dura Lube Engine Treatment immediately helps your engine run cooler and quieter by reducing heat and friction a major cause of engine sludge Dura Lube offers four times more wear pro...

Hummm... what is the pistons compression so far?

I'm from South-Shore Montréal, Canada. I'm a mechanic and know every corner of the Vibe. If I can help anyone to solve problem on their Vibe, It will make me happy.

Regards!

Denis

Rear Sway bar is common problem, unbolt and remove It. then clean (bolts an sway bar orifice with brass wire brush) apply lithium white grease on both parts, reassemble, torque to 80ft/lbs. You also can check your rear shock eye bushing!!! sway bar bolts are hard to remove, make sure to use a two go...