GenVibe - Community for Pontiac Vibe Enthusiasts

jolt

Just want clarification on which manifold you are talking about; the intake manifold or the exhaust manifold? Your first post sounded like you are talking about the exhaust manifold and joatmon post is about the intake manifold. What are the codes, if any?

jolt

I think you need to make a trip to the Toyota dealer and ask for a picture break down of the parts for the axle AND for the transmission case where the axle inters the transmission. In the picture you posted, you can see the groove in your outer sleeve where the retaining ring would be to hold the b...

jolt

Fuel pressure or fuel volume problem possibly. Bad fuel pump or fuel pressure regulator? Fuel line pinched under car? Test fuel pressure and volume by injectors. Do a search on this board as there was a post on how to make a tester hose for the first gen Vibe. A jumped timing chain can make a engine...

jolt

The clock spring in my '09 was changed under a recall. All '09-'10 have electric power steering. The angle senor does feed back to the electric power steering. Is it needed; yes. You will be getting codes for your steering controls if this is not in the right position and your electric steering assi...

jolt

The 2009 vibe do not have a IAC, as they are drive by wire. The idle speed is controlled by the ECM and throttle body. If components in the throttle body are worn, it can make it very hard for the ECM to control the idle speed of the engine. If you have any uncontrolled vacuum leaks it can be imposs...

jolt

Instead of doing one coil over at a time; if you would have taken both off the axle, the axle would have swung down further. That is why the second coil over went on easier then the first one did. You were kind of fighting yourself though the rear solid axle when doing one long coil over and one sho...

jolt

The sulfur smell of rotten eggs is a failed or failing catalytic convertor, as joatmon has said. The question now is what made the convertor fail with only 30.000 miles on it? A convertor should last over 100,000 miles. Rich fuel mixtures will kill a convertor but there are many other things that ca...

jolt

You can use this web site or their app to check gas prices around the US. I have used their trip planner, as it tells you where to stop for the best prices using your cars gas mileage rating and tank capacity to figure the best points to stop at for pricing and range of your vehicle. https://www.gas...

jolt

Does the balance shafts turn over or are they seized? If the shaft will not turn over then the gear will be taken out too. One of the rods and/or rod parts may have wedged into the balance shafts and locked them causing the gear to break. These are questions that do not really matter because the mot...

jolt

Attached are the wiring drawings for the door locks on a 2009 Corolla, which should be close to the same as the 2009 Vibe. Some wire colors may be off but the same basic wiring is happening for the Vibe. As shown there is no relay in the door lock system. Switch and lock motors inputs and outputs ar...

jolt

Of the picture with part of the rod sticking out, you see how dark it is on the rod where the bearing insert would go in the rod, that is carbon/burnt oil on the rod from the rod over heating. This has all the classic signs of running the engine out of oil. The rod that is thrown off is the rod that...

jolt

Nothing that cheap around me. $1.87/gal but it is always about $0.10 higher in the town where I live. I wonder what they are doing with the expensive alcohol now that the gas is so cheap? More tax dollars at work turning food into alcohol for fuel to mix with gas but I doubt the refinery is added mu...

jolt

Plugged cat, doing a search: https://shop.advanceautoparts.com/r/advice/car-maintenance/is-your-catalytic-converter-bad https://www.2carpros.com/articles/how-to-test-a-catalytic-converter Check for codes (P0420 is common for a cat), past history of problems, temp check, and the age old way of checki...

jolt

It cranks over fine. Immediately I thought of the fuel pump as apparently there has been an issue with fuel pump pressure on these. It has over 250k km on it so I fugured it was probably about time. I put a new pump in (Denso) which didn't remedy the problem. I removed the plugs (replaced last fall...

jolt

Here is link to info on pulley for alternator: https://www.rockauto.com/en/moreinfo.php?pk=1872584&cc=1442296&jsn=2218&_nck=Ekt6BqBF1pwlXdx0gYlm1eLc36x7RagAV9qWoBGYzks2kIIGcMG6lE5GS9putP7wmUxgSGze%2FrPdR46WKSRoLyomJamzzG810PitvmOfG4gBYAKT%2Fiy1a%2Bdcj5hpNjQaThqB1phlSeyEoIvMgcaAmAjFTLT6pU...

jolt

You want to check these pages out for the testing your asking for: http://madstyle1972.com/Repair/18/20iajc04/onvein40.pdf http://madstyle1972.com/Repair/18/20iajc04/inspec40.pdf From what you have described above, if it was a GM made car, I would be checking the crankshaft position sensor. In the t...

jolt

So if you remove the belt, and run the engine for less than a minute, the noise is gone? Try putting some baby powder on the face of the belt and then start it and see if the noise went away. The baby power acts as a release agent for the belt in the pulley's. This is not a fix but a test as the bab...

jolt

That is the link that showed the tester from GM that is used to hook to the lines. If I remember that was for a second gen Vibe. I would guess that the first gen would be close to the same thing, but if I remember right, the first gen took a different tester hose setup then the second gen did. Here ...

jolt

Hi Caretaker, You may want to check this link out about the Toyota recall on window switches. I am not sure about what year you are working on but I remembered something about the window switches. Here is link: https://www.toyotanation.com/threads/window-switch-recall.1226745/ Do not clean the greas...

jolt

One more for the MVB:

jolt

Here are more pic's. Also note that there are two different models of four speed transmissions used in the second gen Vibes; the MVA model 4 speed and the MVB model 4 speed. You have stated which 4 speed you have. The above or first pic I posted is for the MVA 4 speed. The pic's I post below are for...

jolt

I do not know for sure but as a general rule if it has a chain it is interference. If it has a belt, it may or may not be interference; depends on when engine was made. Bent valves are not the end of the world for an engine but will require more work then just a chain. The 2.4L engine is the stock e...

jolt

Here is a break down of the parking pawl location in the 4 speed. There is some internal linkage that can be seen when the valve body is removed, but you can not see the pawl assembly. If the valve body is removed, be very careful as the info I have shows a couple of pistons and springs that will fa...

jolt

The hole in picture #2 looks to be from the inside to the outside, see edges of the break and how they are tapered. The bolt that is bent looks to be a rod bolt but that is just guessing as one can not determine it's relative size. This has all the signs of a connecting rod coming off or loose. With...

jolt

Here is video that may help you find your shorts: https://www.youtube.com/watch?v=M4LGykZiRtY

jolt

Why did you replace fuses?

jolt

Everything wears out, it is just a matter of time. Most people do not lubricate their keys and tumblers so they do wear out. I have had to replace a couple key assemblies in my life time because of being worn out. By the time they get to the point yours is at, there just isn't a lot you can do but r...

jolt

I would next clean the mass air flow sensor with mass air flow sensor cleaner. After that, run engine and start spraying all the air intake hoses and connection with throttle body cleaner. Spray all tubing from the mass air flow sensor to the throttle body and then from throttle body to cylinder hea...

jolt

You may get a better view of some of the linkage if you pull the pan off, drop the valve body out, and then you may be able to see some of the linkage better. If you do not want to do this then take it to transmission shop as they may be able to see if the problem is deeper inside transmission. From...

jolt

Running "rich" air/fuel ratios is defiantly bad for an engine. The excess fuel will wash down the cylinder walls, removing the oil from the upper piston ring. Since the piston ring is always spinning in the piston ring land, the top piston ring groove will wear out because the lubrication ...

jolt

Here is info in attachments (not in order and not step by step) You should be able to figure out what needs to be done. This is to show plastic clips (that break) and can not be replaced without replace the panel. The upper panel around the radio is on by clips too. Last thing is the PDF file about ...

jolt

How thick are your brake pads? The wear clips for thin brake pads will make noise mostly when you apply the brakes but if the pad does not retract away from the rotor, you may get random noise from them. Also do the things Bookworm said and report back your findings so the trouble shooting can conti...

jolt

The clutch is not a cable or linkage operated but is hydraulic. You have your master cylinder and a slave cylinder. If you get air in the system, you will get weird things happening and the clutch can get so that it does not work smoothly or be predictable in it operation. By working the clutch, you...

jolt

olliesshop, as for parts places; Rock Auto Parts has the widest range of brands from any one supplier and parts pricing is pretty good too. The thing you have watch for with RA is the shipping costs. You need to try to get all your items from the same warehouse, if possible, to keep the shipping cos...

jolt

I have used KYB struts on a mini van I had and I would have no problems using them again. I would say the KYB's are close to OEM and the Monroe's are a little softer. After my Monroe quick strut install on my Vibe, I would buy the parts and put the struts together myself. You can read below what I f...

jolt

Hopefully you can get healed up. I had something like that when I was young. Doctor had me on PT, a lot of ice, and sonic heat. It took awhile and did heal up. You do not what to do nothing, or it will just get stiff, but you can not over do it also. Take care and don't push yourself to hard.

jolt

As for the scanners, I have a Launch 129 (I think that's the model), and it does not work under GM. It does work under Toyota Matrix so you may try that. First thing is to un-plug connectors, check wiring, and re-seat connectors as andrewclaus refers too. Check wiring at ECM for power (voltage). Mak...

jolt

You measured 7.5 volt between the two points that you had the test leads hooked to. Try moving the ground lead of your meter to a different ground location (the dash frame) and see if the voltage changes. If the new reading is now above 12 volts, you have a bad ground. If voltage is still low, you n...

jolt

Grounds are the worst to trouble shoot as the electrical signals can back feed through other wires in search of a ground to try and complete the circuit. This then messes with the other signals and you end up with multiple electrical problems. You can never have to many grounds; good grounds that is.

jolt

As long as you do not need the fob, the dealer should be able to cut you a key from the VIN number on your Vibe as zbyers has said. A new fob would have to be programmed into the car and that would be done at the dealer's shop. Once you have the key made you can drive the car to the shop and have th...

jolt

You could check the adjustment of the pedal if the clutch is engaging to close to the floor, it may help. See the thread.... viewtopic.php?f=20&t=46586&p=522254&hil ... nt#p522254

jolt

This may help. It shows the good and bad patterns and how the trace the cause down. After checking wiring and connections for the sensor output and heater, check for air leaks in the exhaust system.

jolt

Hi Bookworm, As you have found out, the color of the anti-freeze means nothing really as each manufacture colors the anti-freeze as they like. I use Peak Global Lifetime anti-freeze that I get at Menards on sale for $4.99 or less a gallon. It is the 50/50 pre-mixed but I figure I would have to buy d...

jolt

Oil flow...the new oil may be more free flowing then your old oil was. Oil thickens up as it gets old and the additives get used up in the oil. Also the heat and breakdown of old oil see the lighter hydrocarbons burn off, which thicken the oil too. The thicker oil will not flow through the partially...

jolt

One question I have is what's the best lube for the sleeves? I've used antiseize between the sleeves and bolts, but I know there are specific lubes for caliper sleeves. Here are five good ones: CRC 5339 Brake Caliper Grease. Mission Automotive Silicon Grease. Napa Sil Glyde Lubricating. Permatex Br...

jolt

There is no tightening a loose pulley, something is bad and needs to be replaced as you have found out. There are differences in the 1.8L and 2.4L engine and you do not state which one you have. The 2009 and 2010 Vibes do not have power steering pumps as they use electric motor steering assist for t...

jolt

Cables do wear out and need to be replaced when bad. Jack the rear wheels off the ground, spin each tire by hand. They should spin freely. Next apply the parking brake and try to spin each wheel, they should not spin. Release the parking brake and try to spin each wheel by hand, they should spin fre...

jolt

Are you referring to the CARLSON H5124 sleeves that are listed for the 2003 Vibe GT rear at Rockauto?

https://www.rockauto.com/en/moreinfo.ph ... cc=1432957

https://www.rockauto.com/en/catalog/pon ... +kit,11515

jolt

Manual or automatic transmission? Kind of odd that this would happen at 158K miles. Others on this forum have talked of replacing the timing chain in the car. Use the search to find and check these posts out. Most engines that have a timing chain will bend valves in the cylinder head when the chain ...

jolt

It's part of the whole Clean Air Act, which is "Punish the petrochemical producers." (mind you, I've never heard of anyone working for the EPA getting rid of their SUV's) And I have never seen a petrochemical producer go broke or loose money so they are not being punished. They just pass ...

Search found 946 matches